RGT Technology, LLC . . .

Filter by Category
Unavailable
Filter by Manufacturer
Unavailable
Part Number Manufacturer Description Brand Price & Lead Time
ECM-PCIe8300-DE ESD ESD ECM-PCIe/8300-DE I/O Controller - Dual NIC intelligent EtherCAT-Master PCI Express board, Master API and 'EtherCAT Workbench' support Simple Type: I/O Controller The ECM-PCIe/8300 is a PC board designed for PCI Express slots. It features an on board running EtherCAT master (ECM) in a real- time environment. Two RJ45 sockets are available to connect EtherCAT slave segments. These two interfaces can be used to either control two independent EtherCAT slave segments without support for EtherCAT cable redundancy or to control a single EtherCAT slave segment with support for EtherCAT cable redundancy. In combination with an optional 1 GE switch with VLAN support, the control of even more individual slave segments is supported. The board turns any PC into an EtherCAT master where initialization and control of the EtherCAT segments are completely handled in the real-time environment of the master interface. Time and performance critical tasks are executed in a deterministic way without any influence of the PC's hardware, operating system, device driver, etc. The PC's network interface remains available for e.g. standard TCP/IP communication. Download the datasheet (PDF) Request Quote
ECS-PCIe1100 ESD ESD ECS-PCIe/1100 I/O Controller - PCI Express board with EtherCAT slave controller ET1100 Simple Type: I/O Controller The ECS-PCIe/1100 is a PC board designed for PCI Express slots. It features an EtherCAT slave using the Ethernet physical layer via two RJ45 Ethernet sockets.The board uses the ET1100 EtherCAT slave controller (ESC) ASIC that comes with 8 kBytes memory and 8 EtherCAT sync managers. The ET1100 ESC address space is directly mapped to the PCIe address space. The ECS-PCIe/1100 integrates any PC into an EtherCAT network and makes it an EtherCAT slave node. The PC can act as I/O node. An EtherCAT master can use several EtherCAT protocols like CoE, FoE and EoE to communicate with the PC. Download the datasheet (PDF) Request Quote
ECX-DIO8 ESD ESD ECX-DIO8 I/O Controller - EtherCAT - digital I/O-Module with 8 channels, 100BASE-TX EtherCAT interfaces compatible to IEEE 802.3 Simple Type: I/O Controller The ECX-DIO8 module is equipped with 8 digital I/Os, each available as input and output. The nominal I/O-voltage value is 24 V. Nominal output current is 0.5 A at 24 V. The ECX-DIO8 module provides industrial digital in-/outputs with two-wire connection in combination with service-friendly wiring of supply voltage. The power supply can be applied via the InRailBus connector (TBUS-connector) integrated in the mounting rail or separately via the clamp-connection. The 100BASE-TX EtherCAT interface is compatible to IEEE 802.3. Download the datasheet (PDF) Request Quote
ECX-PoE-PE ESD ESD ECX-PoE-PE I/O Controller - Power-Extractor for InRailBus, applicable with ECX and CBX units, 24 VDC power supply for InRailBus via Power over Ethernet Simple Type: I/O Controller Designed to use in both ECX and CBX units, the ECX-PoE-PE is a power extractor that provides 24 V power supply voltage for the InRailBus. The power supply voltage feeds through the Ethernet lines (PoE). esd designed the module for hat-rail mounting in a control enclosure. The connectors and status LEDs mount in the front panel. The ECX-PoE-PE supports IEEE 802.03at (PoE+, layer 1 only), and is compatible with IEEE 802.03af (Class 4). Ethernet data (10/100/1000BASE-T) passes through electrically. The ECX-PoE-PE comes with LEDs that indicate the state of operation and the states of the temperature- and the output current control. Download the datasheet (PDF) Request Quote
EPPC-405 ESD ESD EPPC-405 I/O Controller - IBM PPC405GP, 200 MHz 16 MB SDRAM, 4 MB Flash, 2x RS-232, 1x CAN, Power supply voltage 24 VDC Simple Type: I/O Controller The EPPC-405 is a stand-alone Power PC in a strong and compact aluminium case without fan cooling. The powerful IBM PPC405GP with 200 or 266 MHz enables a performance of up to 375 MIPS. The board is equipped with 16 or 64 Mbyte SDRAM, up to 8 Mbyte Flash and a CompactFlash slot to carry various memory cards. A non-volatile NVRAM enables the EPPC-405 to save valuable process variables during power off sequences. The EPPC-405 comes with an ETHERNET interface for 10 Mbit/s and 100 Mbit/s nets. It is accessible as 10/100BaseT via RJ45 connector in the front panel. The EPPC-405 (I.2001.03) provides 2 CAN interfaces based on SJA1000 CAN - controllers with transfer rates up to 1 Mbit/s. Designed according to ISO 11898 with electrical isolation and DSUB9 connectors, the EPPC-405 has CAN and RS-232 interfaces. The EPPC-405 (I.2001.02) provides 2 serial interfaces as RS-232 via RJ11 and DSUB9 connector. With 2 serial interfaces only one CAN interface is equipped. The flash memory carries a standard ppcboot and enables the EPPC-405 to boot various operating systems from network, onboard Flash or CompactFlash. Thus Linux and VxWorks are directly supported with full support of on-board drivers by esd, others on request. There is also a bunch of higher layer protocols like CANopen, DeviceNet as well as an on-board web server available. With the IEC61131-3 programming and runtime system CoDeSys the EPPC-405 acts like a PLC. Please ask for our CoDeSys flyer. Download the datasheet (PDF) Request Quote
EPPC-405-2 ESD ESD EPPC-405-2 I/O Controller - IBM PPC405GP, 200 MHz 16 MB SDRAM, 4 MB Flash, 1x RS-232, 2x CAN, All connectors accessible at the front pane Simple Type: I/O Controller The EPPC-405 is a stand-alone Power PC in a strong and compact aluminium case without fan cooling. The powerful IBM PPC405GP with 200 or 266 MHz enables a performance of up to 375 MIPS. The board is equipped with 16 or 64 Mbyte SDRAM, up to 8 Mbyte Flash and a CompactFlash slot to carry various memory cards. A non-volatile NVRAM enables the EPPC-405 to save valuable process variables during power off sequences. The EPPC-405 comes with an ETHERNET interface for 10 Mbit/s and 100 Mbit/s nets. It is accessible as 10/100BaseT via RJ45 connector in the front panel. The EPPC-405 (I.2001.03) provides 2 CAN interfaces based on SJA1000 CAN - controllers with transfer rates up to 1 Mbit/s. Designed according to ISO 11898 with electrical isolation and DSUB9 connectors, the EPPC-405 has CAN and RS-232 interfaces. The EPPC-405 (I.2001.02) provides 2 serial interfaces as RS-232 via RJ11 and DSUB9 connector. With 2 serial interfaces only one CAN interface is equipped. The flash memory carries a standard ppcboot and enables the EPPC-405 to boot various operating systems from network, onboard Flash or CompactFlash. Thus Linux and VxWorks are directly supported with full support of on-board drivers by esd, others on request. There is also a bunch of higher layer protocols like CANopen, DeviceNet as well as an on-board web server available. With the IEC61131-3 programming and runtime system CoDeSys the EPPC-405 acts like a PLC. Please ask for our CoDeSys flyer. Download the datasheet (PDF) Request Quote
EPPC-405-DN ESD ESD EPPC-405-DN I/O Controller - IBM PPC405GP, 200 MHz 16 MB SDRAM, 4 MB Flash, 1x RS-232, 1x CAN, 1x CAN fiber optic, Strong aluminium case for hat-rail mounting Simple Type: I/O Controller The EPPC-405 is a stand-alone Power PC in a strong and compact aluminium case without fan cooling. The powerful IBM PPC405GP with 200 or 266 MHz enables a performance of up to 375 MIPS. The board is equipped with 16 or 64 Mbyte SDRAM, up to 8 Mbyte Flash and a CompactFlash slot to carry various memory cards. A non-volatile NVRAM enables the EPPC-405 to save valuable process variables during power off sequences. The EPPC-405 comes with an ETHERNET interface for 10 Mbit/s and 100 Mbit/s nets. It is accessible as 10/100BaseT via RJ45 connector in the front panel. The EPPC-405 (I.2001.03) provides 2 CAN interfaces based on SJA1000 CAN - controllers with transfer rates up to 1 Mbit/s. Designed according to ISO 11898 with electrical isolation and DSUB9 connectors, the EPPC-405 has CAN and RS-232 interfaces. The EPPC-405 (I.2001.02) provides 2 serial interfaces as RS-232 via RJ11 and DSUB9 connector. With 2 serial interfaces only one CAN interface is equipped. The flash memory carries a standard ppcboot and enables the EPPC-405 to boot various operating systems from network, onboard Flash or CompactFlash. Thus Linux and VxWorks are directly supported with full support of on-board drivers by esd, others on request. There is also a bunch of higher layer protocols like CANopen, DeviceNet as well as an on-board web server available. With the IEC61131-3 programming and runtime system CoDeSys the EPPC-405 acts like a PLC. Please ask for our CoDeSys flyer. Download the datasheet (PDF) Request Quote
EPPC-405-HR ESD ESD EPPC-405-HR I/O Controller - IBM PPC405EP, 133 MHz 32 MB SDRAM, 8 MB Flash, Small top hat rail mounting enclosure Simple Type: I/O Controller The EPPC-405-HR is a stand-alone PowerPC in a small top hat rail mounting enclosure without fan cooling. The powerful IBM PPC405EP runs with 133 MHz clock rate. The board is equipped with 32 Mbyte SDRAM, up to 8 Mbyte Flash. LEDs display the modules status. The EPPC-405-HR comes with an ETHERNET interface for 10 Mbit/s and 100 Mbit/s nets. It is accessible as 10/100BaseT via RJ45 connector in the front panel. Equipped with a CAN interface based on the SJA1000 CAN-controller with transfer rates up to 1 Mbit/s, designed according to ISO 11898, and opto-isolated, the EPPC-405-HR has a serial RS-232 interface for terminal, and debugging is accessible via a RJ12 connector. The standard operating system is Linux, but VxWorks BSP is available as well. Other real time operating systems are available on request. With the IEC61131-3 programming and runtime system, CoDeSys, the EPPC-405 acts like a PLC. Please ask for our CoDeSys flyer. Download the datasheet (PDF) Request Quote
EPPC-405-HR-266 ESD ESD EPPC-405-HR-266 I/O Controller - IBM PPC405EP, 266 MHz 32 MB SDRAM, 8 MB Flash, 10/100BaseT ETHERNET, CoDeSys programming system Simple Type: I/O Controller The EPPC-405-HR is a stand-alone PowerPC in a small top hat rail mounting enclosure without fan cooling. The powerful IBM PPC405EP runs with 133 MHz clock rate. The board is equipped with 32 Mbyte SDRAM, up to 8 Mbyte Flash. LEDs display the modules status. The EPPC-405-HR comes with an ETHERNET interface for 10 Mbit/s and 100 Mbit/s nets. It is accessible as 10/100BaseT via RJ45 connector in the front panel. Equipped with a CAN interface based on the SJA1000 CAN-controller with transfer rates up to 1 Mbit/s, designed according to ISO 11898, and opto-isolated, the EPPC-405-HR has a serial RS-232 interface for terminal, and debugging is accessible via a RJ12 connector. The standard operating system is Linux, but VxWorks BSP is available as well. Other real time operating systems are available on request. With the IEC61131-3 programming and runtime system, CoDeSys, the EPPC-405 acts like a PLC. Please ask for our CoDeSys flyer. Download the datasheet (PDF) Request Quote
EPPC-405-LW ESD ESD EPPC-405-LW I/O Controller - IBM PPC405GP, 200 MHz 16 MB SDRAM, 4 MB Flash, 1x RS-232, 1x CAN, 1x CAN fiber optic interface Simple Type: I/O Controller The EPPC-405 is a stand-alone Power PC in a strong and compact aluminium case without fan cooling. The powerful IBM PPC405GP with 200 or 266 MHz enables a performance of up to 375 MIPS. The board is equipped with 16 or 64 Mbyte SDRAM, up to 8 Mbyte Flash and a CompactFlash slot to carry various memory cards. A non-volatile NVRAM enables the EPPC-405 to save valuable process variables during power off sequences. The EPPC-405 comes with an ETHERNET interface for 10 Mbit/s and 100 Mbit/s nets. It is accessible as 10/100BaseT via RJ45 connector in the front panel. The EPPC-405 (I.2001.03) provides 2 CAN interfaces based on SJA1000 CAN - controllers with transfer rates up to 1 Mbit/s. Designed according to ISO 11898 with electrical isolation and DSUB9 connectors, the EPPC-405 has CAN and RS-232 interfaces. The EPPC-405 (I.2001.02) provides 2 serial interfaces as RS-232 via RJ11 and DSUB9 connector. With 2 serial interfaces only one CAN interface is equipped. The flash memory carries a standard ppcboot and enables the EPPC-405 to boot various operating systems from network, onboard Flash or CompactFlash. Thus Linux and VxWorks are directly supported with full support of on-board drivers by esd, others on request. There is also a bunch of higher layer protocols like CANopen, DeviceNet as well as an on-board web server available. With the IEC61131-3 programming and runtime system CoDeSys the EPPC-405 acts like a PLC. Please ask for our CoDeSys flyer. Download the datasheet (PDF) Request Quote
EPPC-405-UC ESD ESD EPPC-405-UC I/O Controller - IBM PPC405EP, 200 MHz, 2x RS-232, 1x RS-485, 2x CAN, 2x RS-232, 1x RS-485, 2x CAN, Aluminum case for hat-rail mounting Simple Type: I/O Controller The EPPC-405-UC is a stand-alone PowerPC in a slim line aluminum case without fan cooling. The powerful IBM PPC405EP with 133 to 266 MHz enables a performance of up to 375 MIPS. The board is equipped with up to 64 Mbyte SDRAM, 1 Mbyte NOR-Flash, up to 128 Mbyte NAND-Flash and a CompactFlash slot. The EPPC-405-UC comes with an ETHERNET interface for 10 Mbit/s and 100 Mbit/s networks. It is accessible as 10/100BaseT via RJ45 connector in the front panel. The EPPC-405-UC provides 2 CAN fieldbus interfaces based on SJA1000 CAN-controllers with transfer rates up to 1 Mbit/s. esd electronics, Inc. designed the EPPC-405-UC according to ISO 11898 with opto-isolation, Mini-Combicon connectors, 2 USB host interfaces and 3 serial interfaces (two RS-232 and one RS-485). The NOR-flash memory carries a universal boot loader (U-Boot) that enables the EPPC-405-UC to boot various operating systems from network, on-board Flash, or CompactFlash directly supporting Linux and VxWorks and others on request. esd electronics supports on board peripheral drivers. The EPPC-405-UC supports higher layer protocols such as CANopen as well as an available on-board web server. With the optional IEC61131-3 programming and runtime system CoDeSys, the EPPC-405-UC acts like a PLC. Please ask for our CoDeSys flyer. Download the datasheet (PDF) Request Quote
ESD6057-SSAMP ESD ESD Printed Circuit Board Simple Type: TBD Request Quote
EtherCAN ESD ESD EtherCAN I/O Controller - CAN-ETHERNET-Gateway 2 MB Flash, 16 MB SDRAM, CAN over Ethernet Simple Type: I/O Controller The EtherCAN is an ETHERNET-CAN gateway with an NET +50 ARM processor that controls the data transfer between CAN and ETHERNET. Designed for hat-rail mounting in a control enclosure it has connectors and status LEDs mounted in the front panel. The complete firmware for the data transfer between the nets is stored onboard in Flash-EPROM. Additionally, software-drivers are available for Windows NT/2000/XP, and Linux as well as other operating systems upon request. The monitor program CANscope is included in the scope of delivery. Designed for 10 Mbit/s and 100 Mbit/s nets, the ETHERNET interface is accessible through a RJ45 connector in the front panel. Download the datasheet (PDF) Request Quote
EtherCAN2 ESD ESD EtherCAN/2 I/O Controller - CAN-Ethernet-Gateway, 200 MHz ARM-9 microcontroller (MCU), Ethernet interface Simple Type: I/O Controller The EtherCAN/2 is a gateway to transmit data between CAN and Ethernet. The module is designed for hat-rail mounting in a control enclosure as a backward compatible replacement for the EtherCAN gateway (C.2050.02). The gateway has a build-in HTTP server which allows Web based configuration and maintenance. Diagnostic events and messages during runtime can be optionally indicated using the syslog protocol or by sending an email. The gateway firmware can also be updated via the Web interface Drivers for Windows and Linux are available which integrate the CAN gateway as a virtual CAN device on the host, programmed via the common NTCAN-API available for all esd CAN adapter. This allows using all applications, CAN protocol stacks (CANopen, J1939, etc.) and tools (CAN SDK, CANreal, etc.) available for the host platform. In addition the gateway supports the UDP based disclosed and documented Ethernet Low Level Socket Interface (ELLSI) protocol for host platforms which are currently not covered with a dedicated driver. Download the datasheet (PDF) Request Quote
EtherCAN2-S7 ESD ESD EtherCAN/2-S7 I/O Controller - Industrial Ethernet/UDP Gateway, incl. S7-example project with function modules to interface a S7-300/400 Simple Type: I/O Controller The EtherCAN/2 is a gateway to transmit data between CAN and Ethernet. The module is designed for hat-rail mounting in a control enclosure as a backward compatible replacement for the EtherCAN gateway (C.2050.02). The gateway has a build-in HTTP server which allows Web based configuration and maintenance. Diagnostic events and messages during runtime can be optionally indicated using the syslog protocol or by sending an email. The gateway firmware can also be updated via the Web interface Drivers for Windows and Linux are available which integrate the CAN gateway as a virtual CAN device on the host, programmed via the common NTCAN-API available for all esd CAN adapter. This allows using all applications, CAN protocol stacks (CANopen, J1939, etc.) and tools (CAN SDK, CANreal, etc.) available for the host platform. In addition the gateway supports the UDP based disclosed and documented Ethernet Low Level Socket Interface (ELLSI) protocol for host platforms which are currently not covered with a dedicated driver. Download the datasheet (PDF) Request Quote
EtherCAN-ELLSI ESD ESD EtherCAN-ELLSI I/O Controller - UDP/TCPIP Socket-Interface, CANOpen manager, Hat-rail case Simple Type: I/O Controller The EtherCAN is an ETHERNET-CAN gateway with an NET +50 ARM processor that controls the data transfer between CAN and ETHERNET. Designed for hat-rail mounting in a control enclosure it has connectors and status LEDs mounted in the front panel. The complete firmware for the data transfer between the nets is stored onboard in Flash-EPROM. Additionally, software-drivers are available for Windows NT/2000/XP, and Linux as well as other operating systems upon request. The monitor program CANscope is included in the scope of delivery. Designed for 10 Mbit/s and 100 Mbit/s nets, the ETHERNET interface is accessible through a RJ45 connector in the front panel. Download the datasheet (PDF) Request Quote
EtherCAN-Modbus-TCP ESD ESD EtherCAN-Modbus-TCP I/O Controller - MODBUS/CAN-Gateway, ETHERNET protocols: TCP/IP, Modbus/TCP, 10/100BaseT ETHERNET Simple Type: I/O Controller The EtherCAN is an ETHERNET-CAN gateway with an NET +50 ARM processor that controls the data transfer between CAN and ETHERNET. Designed for hat-rail mounting in a control enclosure it has connectors and status LEDs mounted in the front panel. The complete firmware for the data transfer between the nets is stored onboard in Flash-EPROM. Additionally, software-drivers are available for Windows NT/2000/XP, and Linux as well as other operating systems upon request. The monitor program CANscope is included in the scope of delivery. Designed for 10 Mbit/s and 100 Mbit/s nets, the ETHERNET interface is accessible through a RJ45 connector in the front panel. Download the datasheet (PDF) Request Quote
EtherCAN-NT ESD ESD EtherCAN-NT I/O Controller - CAN-ETHERNET gateway bundle w/WinXP/2K & Linux driver, CAN-API, ARM-processor NET+50 Simple Type: I/O Controller The EtherCAN is an ETHERNET-CAN gateway with an NET +50 ARM processor that controls the data transfer between CAN and ETHERNET. Designed for hat-rail mounting in a control enclosure it has connectors and status LEDs mounted in the front panel. The complete firmware for the data transfer between the nets is stored onboard in Flash-EPROM. Additionally, software-drivers are available for Windows NT/2000/XP, and Linux as well as other operating systems upon request. The monitor program CANscope is included in the scope of delivery. Designed for 10 Mbit/s and 100 Mbit/s nets, the ETHERNET interface is accessible through a RJ45 connector in the front panel. Download the datasheet (PDF) Request Quote