VME-PMC-CADDY-3.3P1

ESD

ESD VME-PMC-CADDY-3.3P1 I/O Controller - 3.3V power supply directly connected to VMEbus 3.3V, not generated from 5V supply, extended temperature range on request Simple Type: I/O Controller The VMEbus unit PMC-CADDY is a VME64 base unit that can carry up to two PMC modules of normal size or one module of double size. For the VMEbus connection, the VME-PCI Bridge UNIVERSE CA91C142 by Tundra With an internal clock rate of 33 MHz is used. The CA91C142 interface can operate either as either slave or as Master on the VMEbus. If the board operates as master, it supports a 4-level arbiter. The PMC-CADDY operates with a data width of up to 32 bits and with 32 address signals on the VMEbus. You can apply the VMEbus interrupt to any of the seven interrupt-request lines. The board connects to the VMEbus by two 160-pin VG-connectors according to IEC603-xx on VME64 extensions. A red LED shows an active VMEbus-interrupt request in the front panel and a yellow LED shows a VMEbus access onto the board. Draft standard IEEE P1386/Draft 2.0 is the standard used for both PMC plug-in units' design except for the standard I/O pin routing. This design makes it possible to insert any PMC modules on the market. In addition to the connectors for the PMC address/ data and control signals, every plug-in unit of the PMC-CADDY has an I/O-connector that applies the I/O signals of the PMC modules to VMEbus connector P2. Two different P2 pin assignments are available: In the standard configuration, each P2-pin connects to one I/O-pin of the PMC modules (acc. to PMC-Update of FORCE ™, Table 1, Author: Wayne Fischer, Director of Strategic Programs CMC/PMC Working Groups Chair, 22.10.96). In the option -32P, the pin assignment is acc. to IEEE P1386/Draft 2.0, Table 6-3. This pin assignment offers to connect the two PMC-modules via P2, because several PMC-I/O-signals short at P2. Download the datasheet (PDF)

VME-PMC-CADDY

ESD

ESD VME-PMC-CADDY I/O Controller - VMEbus base board for two single PMC modules, P2-pin assignment acc. to PMC-Update from 22.10.96 (no interconnection between PMC-modules) Simple Type: I/O Controller The VMEbus unit PMC-CADDY is a VME64 base unit that can carry up to two PMC modules of normal size or one module of double size. For the VMEbus connection, the VME-PCI Bridge UNIVERSE CA91C142 by Tundra With an internal clock rate of 33 MHz is used. The CA91C142 interface can operate either as either slave or as Master on the VMEbus. If the board operates as master, it supports a 4-level arbiter. The PMC-CADDY operates with a data width of up to 32 bits and with 32 address signals on the VMEbus. You can apply the VMEbus interrupt to any of the seven interrupt-request lines. The board connects to the VMEbus by two 160-pin VG-connectors according to IEC603-xx on VME64 extensions. A red LED shows an active VMEbus-interrupt request in the front panel and a yellow LED shows a VMEbus access onto the board. Draft standard IEEE P1386/Draft 2.0 is the standard used for both PMC plug-in units' design except for the standard I/O pin routing. This design makes it possible to insert any PMC modules on the market. In addition to the connectors for the PMC address/ data and control signals, every plug-in unit of the PMC-CADDY has an I/O-connector that applies the I/O signals of the PMC modules to VMEbus connector P2. Two different P2 pin assignments are available: In the standard configuration, each P2-pin connects to one I/O-pin of the PMC modules (acc. to PMC-Update of FORCE ™, Table 1, Author: Wayne Fischer, Director of Strategic Programs CMC/PMC Working Groups Chair, 22.10.96). In the option -32P, the pin assignment is acc. to IEEE P1386/Draft 2.0, Table 6-3. This pin assignment offers to connect the two PMC-modules via P2, because several PMC-I/O-signals short at P2. Download the datasheet (PDF)

VME-AIO16

ESD

ESD VME-AIO16 CPU Board - CPU 68340, 25 MHz, 256 kbytes SRAM, 16 A/D channels (16 Bit), UIN = ±10 V, 4 D/A channels (16 Bit)Max. sample rate 45 kHz (only one channel used) Simple Type: CPU Board VME-AIO16 is an intelligent VMEbus board, containing 6 or 16 analog differential inputs and is ideally suited for fast and flexible data acquisition. It includes all necessary components on a VMEbus 6U board and needs one slot. The AIO16 contains a local MC 68340 CPU at 25 MHz for the execution of complex data acquisition algorithms. The CPU section of the AIO16 contains 256 kbytes of SRAM, EPROM and two RS-232 interfaces. Configuration parameters may be stored in an EEPROM. AIO16 contains 256 kbytes of shared SRAM, as well, to form the interface between local CPU and VMEbus. Designed for use of A/D converters with 16 bits resolution, the AIO16 can also be equipped with 12 bits resolution converters. The input voltage range with standard components is ±10 V. By varying the resistance values, other voltage ranges as well as current measurement (±20 mA) are possible. The A/D converters synchronize via an external trigger signal or via software. The included software allows you to obtain the following sampling rates: the maximum sampling rate from trigger signal to reception of the A/D-data in the SRAM is 33 kHz when sampling all 16 channels synchronously. If sampling only 8 channels synchronously, the maximum sampling rate is 40 kHz, for just one channel it is 45 kHz. In addition to the analog inputs, the AIO16 board contains 4 bipolar ±10 V D/A converter outputs with a resolution of 16 bits. These D/A converters allow internal calibration and offset adjustment of the input amplifiers. Connect each D/A converter to one of four A/D inputs via a multiplexer for this result. Of course, the user can also use these D/A converter outputs directly as process outputs. Download the datasheet (PDF)

PMC-DVI

ESD

ESD PMC-DVI I/O Controller - Graphics adapter board, DVI-I (digital video interface) connector including RGB-analog Simple Type: I/O Controller The PMC-DVI is a graphics board in ‘single’ PCI mezzanine card size with the powerful graphics controller 69030 offering display modes from 640x480 (true color) at 85 Hz up to 1600x1200 (16 bit colors) at 60 Hz. The DVI-I-interface design controls CRT-monitors by analog video signals as well as TFT-monitors by digital video signals. The board is equipped with a Mini-DSUB9-connector as PS2- interface. With an adapter, you can connect a PS2-keyboard and a PS2-mouse to this port simultaneously. Graphics drivers are available for VxWorks, RTOS/UH, Linux, QNX, Windows 98/NT2000, and other drivers upon request. Download the datasheet (PDF)

CAN-CBM-Bridge2-ME

ESD

gh Simple Type: I/O Controller